If a contractor tells you your chimney needs a “new top,” it is worth knowing exactly which part they mean. Three different components protect the top of a chimney — the cap, the chase cover and the crown — and they are not interchangeable. Which ones you have depends on what kind of chimney you have.
The quick answer
- Chimney cap: a metal cover with a mesh screen over the flue opening. Every chimney should have one.
- Chimney crown: the concrete slab on top of a brick or masonry chimney, around the flue.
- Chase cover: the metal lid covering the entire top of a prefab (factory-built) chimney that is framed and covered in siding or stucco.
So a masonry chimney has a crown and a cap. A prefab chimney has a chase cover and a cap.
First: which kind of chimney do you have?
Look at the outside of your chimney:
- Brick, block or stone all the way up — it is a masonry chimney with a crown.
- Siding, stucco or wood panels on a framed box — it is a prefab chimney with a chase cover.
Not sure? Our guide to prefab vs. masonry chimneys explains how to tell.
What a chimney cap does
The cap sits directly over the flue opening. It has a lid that keeps rain out and a mesh screen that keeps out birds, squirrels, raccoons and leaves. The mesh also acts as a spark arrestor, stopping embers from landing on the roof.
How caps fail in Florida: galvanized caps rust in salt air, sometimes in just a few years. Caps that are too small or too low can choke the draft and cause smoke in the room. Loose caps blow off in storms.
When to replace: if it is rusted, bent, loose, missing its screen, or missing entirely. Stainless steel is the right choice near the coast. See chimney cap installation.
What a chimney crown does
On a masonry chimney, the crown is the cement or concrete slab that covers the top of the brick around the flue tile. Its job is to shed water away from the flue and off the sides of the chimney so it doesn’t soak into the brick.
A well-built crown is sloped, overhangs the brick by a couple of inches with a drip edge, and has a small gap (bond break) around the flue tile so the two can expand separately.
How crowns fail in Florida: many original crowns are just a thin layer of mortar with no slope or overhang. Daily heat and sudden rain cycles crack them, water gets in, and the brick below starts to deteriorate.
When to repair: hairline cracks can be sealed. Larger cracks or crumbling crowns need repair or a rebuild. See chimney crown repair.
What a chase cover does
Prefab chimneys are a metal flue pipe inside a wood-framed box (the chase). The chase cover is the metal lid on top of that box. It keeps rain out of the chase and has an opening for the flue pipe, which is sealed by a storm collar, with a cap on top.
How chase covers fail in Florida: most original covers are thin, flat galvanized steel. Water pools on top, the coating wears off, and the cover rusts through — often within 10 to 20 years, and faster near the Gulf. Screws through the top create more leak points and rust stains down the siding.
When to replace: rust, pooling water, holes, sagging or rust streaks on the chase. A custom-sized, sloped stainless cover is the long-term fix. See chase cover replacement.
Side-by-side comparison
- Cap — covers the flue opening — found on all chimneys — main job: keep out rain and animals — typical failure: rust, wrong size, missing.
- Crown — covers the top of brick — found on masonry chimneys — main job: shed water off the masonry — typical failure: cracking.
- Chase cover — covers the top of a framed chase — found on prefab chimneys — main job: keep water out of the chase — typical failure: rust-through and pooling.
Why the difference matters
If your prefab chimney is leaking because the chase cover has rusted through, a new cap won’t fix it. If a masonry crown is cracked, a cap won’t stop water soaking into the brick. Make sure any repair quote names the specific part that has failed.
Frequently asked questions
Does every chimney need a cap?
Yes. Even if you rarely use your fireplace, a cap keeps water and animals out of the flue.
Can I install a chase cover on a brick chimney?
No. Brick chimneys use a crown. Some masonry chimneys get a metal top or a multi-flue cap, but that is different from a chase cover.
Which part is most likely causing my leak?
On prefab chimneys in Florida, the chase cover. On masonry chimneys, the crown and flashing. Our guide on why chimneys leak goes through every cause.
Need help with your chimney in Pinellas County?
Mason Chimney Repair inspects and repairs chimneys and fireplaces across Pinellas County, from Tarpon Springs and Dunedin to St. Petersburg, Clearwater and the Gulf beaches. We find the real cause, show you photos, and give you a written price before any work starts. Call (727) 710-5681 or request an inspection online.
